|
 
Used Machinery
ALL Used
Machinery
Used
Air Compressors
Used Autobrakes / Sheet Metal Folders
Used Bar Folders
Used
Sheet Metal Brakes
Used Cheek Benders
Used
Cleat Benders / Cleat Folders
Used
Clincher / Fasteners
Used Coil Lines
Used Corner Inserter Machines
Used
Crimping / Beading / Rotary Machine
Used Drill Press
Used
Duct Beading Machine
Used
Duct Insulation Liner Cutters
Used
Flangers / Flanging Machines
Used
Gorelockers / Elbow Machines
Used Grinders
Used HVAC Accessories
Used
HVAC Duct Insulation Pin Spotters
Used
Ironworkers
Used
Laser Cutting Machines
Used Notching
Machines
Used
Pipe Equipment
Used
Pittsburgh Seamers
Used Plasma
Cutting Machines
Used Press Brakes
Used Punching
Machines
Used
Sheet Metal Rolls
Used Roll Formers
Used
Saws
Used Sheet
Metal Shears
Used
Sheet Metal Slitters
Used
Spiral Machines
Used
Welders
|
Advance Cutting systems | Autofold Coilines
ACS AutoFold-iFold
Advance Cutting Systems is pleased
to introduce the i-Fold duct coil line. The i-Fold
brings an affordable coil line to even the smallest duct fabricator.
For contractors who use Ductmate™, Ward™ or MEZ™
knock on duct connectors, the i-Fold cannot be beaten
- The i-Fold offers most of the functionality
of a conventional coil line with the advantage of a vastly reduced
floor space requirement (6ft 6in x 10ft).
- The i-Fold allows the operator to use standard
coil widths, in multiple gauges up to 16ga, and manufacture
ductwork from a minimum of 5in x 5in.
- The fully hydraulic system is controlled by the AutoFold v8
Control System that has been designed specifically for this
machine. The input is through a dedicated 14in touch screen
controller that utilizes a Windows™ CE platform to run
the AutoFold Standard Software Program.
- The AutoFold Standard Software includes a Jobs Program.
- Ductwork is produced at an average rate of 1 piece every 20
seconds (depending on the size of the duct). The i-Fold retains
the same production rate as the larger AutoFold machines.
- The AutoFold Standard Software includes a Jobs Program.
The i-Fold can produce the following:
- Flat sheet cut to length blanks
- "L" Sections
- "U" Sections
- Fully Wrapped Duct Sections
AF-iFold Secifications:
- 7 Roll Leveller System consisting
of 2 Entrance Drive Rolls, 3 Leveller Rolls & 2 Exit Bead
Rolls.
- Shear Blades, 4 sides, upper and lower, for extended life
- Maximum Working Gauge: 16ga
- Maximum Material Width: 5ft
- AutoFold v8 Controller with full AutoFold Windows™
CE Software including make quick, jobs and self-diagnostics
programs.
- 14in Touch Screen Monitor with fittings, mounted on the left
or right side of the machine.
- One “A” frame coil holder with spindle. (Maximum
coil weight 10,000lbs at 5ft wide)
Return to TOP
ACS Duct Seam
Closer
Overview:
The Duct Seam Closer is designed to seam rectangular
ducts.
The machine is a solid welded steel construction.
Increases productivity and can be operated with one person.
Includes a 1 year warranty as standard.
The DCS roll-forming machine takes HVAC ductwork
that has previously been formed into “L” or Fully
Wrapped Duct Sections, ot even large duct that has been fabricated
in 4 individual pieces, applies a male and female seam and closes
the seam together quickly, quietly and tightly. Basically, a non-seamed
section of duct goes in one end and a completely closed seam section
of duct comes out the other end. The capacity of the DSC is 26
– 20 gauge.
Specifications for the DSC lock are listed in
the SMACNA HVAC Duct Construction Standards, Second Addition,
1995. The DSC lock is referred to as a Double
Corner Seam or as a Slide Lock Seam. The male and female allowance
of the DSC is similar to that of a male and female Pittsburgh
seam. (ACS recommends that you check with your local inspector
for the approval of the DCS lock). ACS
has many contractors using this seam who will be happy to discuss
their satisfaction with it.
The effectiveness of the Duct Seam Closer is
enhanced when used in conjunction with the AutoFold Coil Line.
The Duct Seam Closer also works well with Ductmate
or Ward knock-on-connectors and can also be used with ductwork
that already has the Drive Clear edge turned over. (The Duct
Seam Closer does not work with the pre-insulated ductwork
or TDC* or TDF* duct connectors).
*TDC is a registered trademark of Lockformer; TDF is
a registered trademark of Engel Industries.
Return to TOP
Return to
the New Machinery Page
Return to the Home
Page
|
