|
 
Used Machinery
ALL Used
Machinery
Used
Air Compressors
Used Autobrakes / Sheet Metal Folders
Used Bar Folders
Used
Sheet Metal Brakes
Used Cheek Benders
Used
Cleat Benders / Cleat Folders
Used
Clincher / Fasteners
Used Coil Lines
Used Corner Inserter Machines
Used
Crimping / Beading / Rotary Machine
Used Drill Press
Used
Duct Beading Machine
Used
Duct Insulation Liner Cutters
Used
Flangers / Flanging Machines
Used
Gorelockers / Elbow Machines
Used Grinders
Used HVAC Accessories
Used
HVAC Duct Insulation Pin Spotters
Used
Ironworkers
Used
Laser Cutting Machines
Used Notching
Machines
Used
Pipe Equipment
Used
Pittsburgh Seamers
Used Plasma
Cutting Machines
Used Press Brakes
Used Punching
Machines
Used
Sheet Metal Rolls
Used Roll Formers
Used
Saws
Used Sheet
Metal Shears
Used
Sheet Metal Slitters
Used
Spiral Machines
Used
Welders
|
Shears
Roper
Whitney 10M14 Mechanical Shear
Roper Whitney's 10M14 Mechanical Shear is
the latest addition to the Roper Whitney line
of shears. Manufactured in the United States, the 10M14
Mechanical Shear is of rugged construction, weighs
in at 5,500 pounds, and this shear is powered by a 5 horsepower
motor. The 10M14 produces up to 35 strokes
per minute.
Standard Features Of The Roper Whitney 10M14 Mechanical
Shear:
- Made in the U.S.A.
- Rugged Welded Construction
- Single or Continuous Cycle
- Accurate Table Side-Squaring Gauges
- Recessed Inch/Metric Bed Scales
- Combination Material Hold-Down/Finger Guard with Non-marring
Urethane and Positive Spring Actuation
- High Carbon/High Chrome Long Life Tool Steel Blades
- Upper and Lower Blades Interchangeable
- Non-Metallic Gibs
- Maintenance Free Self Lubricating Bearings
- Fully Guarded Safety Foot Switch
- Low Power Consumption
- Smooth Quiet Reliable Operation
Additional Options for the Roper 10M14 Shear:
- Front arms
- Side Squaring Arms in 4', 8', or 12' Lengths with
Fixed Stop and Inlaid Scale
- Squaring Arm Flip Stop
Backgauge Options For the Roper Whitney 10M14 Mechanical
Shear:
Rear Operated Manual with Precision Scale Front Operated Manual
with Chain Drive and Position Counter DRO-Motor Driven with
Digital Readout NC-Motor Driven with encoder Feedback, and Digital
Readout with Five Preset Positions
Roper Whitney Mechanical Shear 10M14 Specifications:
- Capacity - 14 Ga.mild steel
- Working Length - 121.25 inches
- Back Gauge Travel - 24 inches
- Approximate Weight - 5500 lbs.
- Power - 5 hp
- Standard Voltage - 230 vac 3 hp 60 Hz
- Strokes Per Minute - 35
 Betenbender
Betenbender
Mechanical Shears
Betenbender designs simplicity and safety
into its shears -- with an advanced hydraulic system and flexible
operation. These mechanical shears are easy to operate, easy
to maintain and able to withstand the rigors of today's production
demands. A wide range of options for Betenbenders Shears
are available.
Controls:
Push button and switch controls are at your fingertips. The
fully guarded, 2-position 110V footswitch lets you interrupt
the cutting stroke at any point in its cycle.
Easy Material Handling:
A sturdy backgauge and rake angle adjustment minimizes twist
and distortion, making it possible to increase the rake for
cutting heavier stock and extend maximum capacity of the machine.
A 4’ squaring arm with recessed scale makes for fast,
easy measurement with your Betenbender Shear.
Modified High Carbon, High Chrome Reversible Knives:
Betenbender shears provide four separate edges for clean, burr-free
cuts and long blade life. Easy blade gap adjustment means precise
cuts for a wide variety of materials.
Electrical System:
Meets NFPA79 and construction requirements of the ANSI B11.4.
All machines have disconnect switches, magnetic starters, 110/120
volt controls, and 220/460 voltages.
Backgauges:
A Betenbender Shear is capable of shearing 1/8" (10 gauge)
material to the following tolerance: Dimension - The width of
the off-cut portion of the work- piece is within ±0.005
inch of the backgauge setting.
STANDARD FEATURES for BETENBENDER Mechanical Shears:
- 36" Power Backgauge with LED Readout - Inch/Metric
- Power Adjust Variable Rake
- 4’ Squaring Arm with Inlaid Scale
- Hour Meter
- Light Beam Gauge (Shadow Line)
- Single Piece Top and Bottom, HCHC Shock Resistant Knives
with Four Cutting Edges
- Hydraulic Self-Compensating Holddown Bar Assembly
- NEMA Electrics
- All Hydraulic Fluids Included
- American Made Pump, Valves and Motor
- Disconnect Switch
- American Made Hoses and Fittings
- All Steel Construction
- Hydraulic Pressure: 2500 PSI
- Manual Rapid Blade Gap Adjustment (3/8", 1/2",
5/8", 3/4")
- Manual Swing Up Backgauge
OPTIONS AVAILABLE for BETENBENDERS Mechanical Shears:
Power Lift Backgauge, Automatic Power Lift Backgauge, Pneumatic Sheet
Support, Extra Length on Backgauge, Solid Table Top - Bolt on segments,
Machined Solid Top Bed, 48" Support Arms/Front Gauges, Inlaid Scale
0 - 48", Angle Gauge, Electronic Stroke Control, Continuous Stroke,
Stroke Counter, One Shot Lubrication, Automatic Lubrication, Ball Transfers,
Independent Holddown Control, 4' Left Hand Squaring Arm, Extended Squaring
Arm (4’ Standard), Extra Foot Pedal w/Keylock Switch, Keylock
Switch, Flip Up Stops (Squaring Arm), Disappearing Stops (Support Arm),
Increase HP (Increase Stroke), Oil Cooler, Control Panel with Optional
Stroke Control, 3-Position Power Blade Gap Adjustable with Indicator
Lights, Manual Rapid Blade Gap Adjustment (on 1/8" (10ga), 3/16",
1/4"), GO-TO Backgauge Positioner, CNC Backgauge, Neoprene Hold-down
Caps, Dovetail Slots or T-Slots, 220/460 (specify either), Gap Type
Machine (Slitting), Harder grade of high carbon, high chrome knives,
208 Volt and Special Paint Colors
Return to
the Precision Machinery Page
Return
to the Home Page
|
